- #Motorguide xi3 with pinpoint gps how to#
- #Motorguide xi3 with pinpoint gps manual#
- #Motorguide xi3 with pinpoint gps full#
- #Motorguide xi3 with pinpoint gps series#
A paired Xi Series Pinpoint GPS remote is required to complete Keel Calibrationġ.A fixed GPS position (illuminated GPS indicator light) is required to compete Keel Calibration.If your trolling motor has been moved from one boat to another, it is recommended you recalibrate your Xi Series motor to ensure correct heading lock performance, also known as Mounting Angle Keel Calibration. What do I need to do if moving my motor to a new boat? Compass calibration should NOT be completed using your motor for propulsion as this could negatively impact Pinpoint GPS performance.
#Motorguide xi3 with pinpoint gps full#
We recommend 2-3 full calibrations for best results. The more you calibrate, the better the accuracy.A fixed GPS position (illuminated GPS indicator light) and a paired Xi Series Pinpoint GPS remote is required to complete Compass Calibration.For initial installations, repeat steps 1-5 two additional times to ensure the motor is fully calibrated to your specific boat and geographic region. The GPS status indicator light will turn on and a beep will occur, signaling a successful compass calibration.Ħ. Two beeps will occur when very close to completing the second circle. If performing the compass calibration with the boat on the trailer: tow the boat in two complete circles.ĥ. If performing the compass calibration with the boat in the water: use the primary propulsion engine to slowly drive the boat in two complete circles.ī. The trolling motor will emit three ascending-tone beeps and the GPS status indicator light will turn off.Ĥ.
#Motorguide xi3 with pinpoint gps manual#
Press and hold the manual mode button, then press 1, 1, 1. If performing the compass calibration with the boat in the water, verify that you are in a location where your trolling motor and primary propulsion engine will not hit bottom or other obstructions.ģ. (15.2 cm) above the depth collar and the motor. Adjust the motor height so that the bottom of the head is 6 in. If performing the compass calibration with the boat on the trailer: locate a suitable area clear of obstructions to perform the compass calibration.Ģ.
If performing the compass calibration with the boat in the water: locate a suitable area clear of obstructions to navigation (both above and below the waterline) to perform the compass calibrationī. Use your remote to complete Compass Calibration – M111ġ. Many owners have run accessories using a coiled hose method and brackets from RyTek Marine. There are many aftermarket options for installing external accessories on your Xi5. HOW SHOULD I PROPERLY RUN EXTERNAL CABLES ON MY XI TROLLING MOTOR? If a longer length is needed, you should extended the NMEA 2000 backbone cable to a new NMEA "T" within reach. If multiple power nodes are needed to balance the network, they should be added to the same 12v switched source.ĭo NOT extend the NMEA cable from the Xi trolling motor to the NMEA "T". If NMEA networking, ensure your network is powered off a single switched 12v source. Please use this NMEA 2000 Network chart to properly route your NMEA 2000 network.
#Motorguide xi3 with pinpoint gps how to#
Xi Series Pinpoint GPS enabled motors can be NMEA 2000 networked for additional features on your Lowrance/Simrad MFDs by using the Xi Series Pinpoint GPS Gateway Kit (8M0092085) to connect to a NMEA network.Ĭheck out this video to see how to properly network your Xi Series motor. HOW DO I CONNECT MY XI GPS MOTOR TO MY CHARTPLOTTER? Follow the chart below to determine which accessories you will need. If you have a GPS enabled Xi Series motor, you can connect your motor to a compatible Lowrance or Simrad chartplotter. HOW CAN I CONNECT MY MOTOR TO A CHARTPLOTTER FOR ADVANCED NAVIGATION FEATURES? Gray Machete comes standard on all Xi series motors. This includes our Safari, Katana (8M4004173), Gray Machete (MGA089G), and Aluminum Machete (MGA087M) propellers. Xi Series motors are compatible with any MotorGuide propeller with a 3.5” hub. Note: Newer models with an 8pin sonar port would require adapter 010-11613-00. Note: Hook requires an additional adapter cable 000-14068-001 Lowrance 7-pin (XXXXXXXX): Elite, HDS, Hook Our Xi series Quick Release Bracket is also available in White Composite (8M0092063), Black Composite (8M0120717), and Black Aluminum (8M0092064) Which sonar units are motor compatible with my 2D universal transducer? Quick Release Bracket installation video available here. This QRB also works with most competitor hole patterns as well. Yes, our Universal Quick Release Bracket (8M0095972) works with our Tour and Xi Series motors.
0 kommentar(er)
